Calculation tool
SBAR013 — Isolated Amplifier Voltage Sensing Excel Calculator
This calculator provides estimates of the errors associated with using isolation amplifier devices in a voltage sensing configuration.
AMC3330
±1-V input, precision voltage sensing reinforced isolated amplifier with integrated DC/DC
Data sheet
AMC3330
- 3.3V or 5V single supply operation with integrated DC/DC converter
- ±1V input voltage range optimized for voltage measurements with high input impedance
- Fixed gain: 2.0
- Low DC errors:
- Gain error: ±0.2% (max)
- Gain drift: ±45ppm/°C (max)
- Offset error: ±0.3mV (max)
- Offset drift: ±4µV/°C (max)
- Nonlinearity: ±0.02% (max)
- High CMTI: 85kV/µs (min)
- System-level diagnostic features
- Safety-related certifications:
- 6000VPK reinforced isolation per DIN EN IEC 60747-17 (VDE 0884-17)
- 4250VRMS isolation for 1 minute per UL1577
- Meets CISPR-11 and CISPR-25 EMI standards
The AMC3330 is a precision, isolated amplifier with a fully integrated, isolated DC/DC converter that allows single-supply operation from the low-side of the device. The reinforced capacitive isolation barrier is certified according to DIN EN IEC 60747-17 (VDE 0884-17) and UL1577 and separates sections of the system that operate on different common-mode voltage levels and protects low-voltage domains from damage.
The input of the AMC3330 is optimized for direct connection to high-impedance, voltage-signal sources such as a resistor-divider network to sense high-voltage signals. The integrated isolated DC/DC converter allows measurement of non-ground-referenced signals and makes the device a unique solution for noisy, space-constrained applications.
The excellent performance of the device supports accurate voltage monitoring and control. The integrated DC/DC converter fault-detection and diagnostic output pin of the AMC3330 simplify system-level design and diagnostics.
The AMC3330 is specified over the temperature range of –40°C to +125°C.
Technical documentation
No results found. Please clear your search and try again.
View all 36 Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
AMC3330EVM — AMC3330 precision reinforced isolated amplifier with integrated DC/DC converter evaluation module
The AMC3330 evaluation module (EVM) is an evaluation platform for the AMC3330 product, a precision isolated amplifier with an integrated DC/DC converter that powers the high side of the amplifier. AMC3330 is a 7-kV reinforced isolated amplifier designed for use in bipolar voltage-measuring (...)
Simulation model
AMC3330 and AMC3330-Q1 TINA-TI Spice Model (Rev. B)
SBAM446B.TSC (152 KB) - TINA-TI Spice Model
Calculation tool
SBAR020 — Isolated Amplifier Current Sensing Excel Calculator
This calculator provides estimates of the errors associated with using isolation amplifier devices in a current sensing configuration.
Supported products & hardware
Products
Isolated amplifiers
Simulation tool
PSPICE-FOR-TI — PSpice® for TI design and simulation tool
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Reference designs
TIDA-010933 — 1.6kW, bidirectional micro inverter based on GaN reference design
This reference design shows a four-input bidirectional 1.6kW GaN-based microinverter with energy storage capability.
Design guide: PDF
Reference designs
TIDA-010955 — Analog front end for machine learning arc detection in solar applications
This reference design features an analog front end for DC arc detection in solar applications based on artificial intelligence (AI). DC arcing induces a high-frequency noise onto the DC sting current. To detect the arcing frequency, data is acquired and feed into an embedded AI model, which is (...)
Design guide: PDF
Reference designs
TIDA-010232 — AFE for insulation monitoring in high-voltage EV charging and solar energy reference design
This reference design features an electric bridge DC insulation monitoring (DC-IM) method which allows an accurate symmetrical and asymmetrical insulation leakage detection mechanism and an isolation resistance detection mechanism. We present a new generation of isolated amplifiers and switchers (...)
Design guide: PDF
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| SO-MOD (DWE) | 16 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.