Home Motor drivers Brushed DC (BDC) motor drivers
Home
Motor drivers
Brushed DC (BDC) motor drivers

DRV8962

ACTIVE

65-V four-channel half-bridge driver with current sense outputs

Order now
Data sheet

DRV8962

ACTIVE
Data sheet Order now

Product details

Number of full bridges 2 Vs (min) (V) 4.5 Vs ABS (max) (V) 70 Peak output current (A) 10 RDS(ON) (HS + LS) (mΩ) 100 Sleep current (µA) 2 Control mode Independent 1/2-Bridge, PWM Control interface Hardware (GPIO) Features Current Regulation, Current sense Amplifier, Integrated Current Sensing Rating Catalog Operating temperature range (°C) -40 to 125 Topology Push-Pull
Number of full bridges 2 Vs (min) (V) 4.5 Vs ABS (max) (V) 70 Peak output current (A) 10 RDS(ON) (HS + LS) (mΩ) 100 Sleep current (µA) 2 Control mode Independent 1/2-Bridge, PWM Control interface Hardware (GPIO) Features Current Regulation, Current sense Amplifier, Integrated Current Sensing Rating Catalog Operating temperature range (°C) -40 to 125 Topology Push-Pull
HTSSOP (DDV) 44 113.4 mm² 14 x 8.1 HTSSOP (DDW) 44 113.4 mm² 14 x 8.1
  • Four-channel half-bridge driver
    • Independent control of each half-bridge
  • 4.5 V to 65 V operating supply voltage range
  • Low R DS(ON): 50 mΩ for each FET (24 V, 25 °C)
  • High current capacity:
    • DDW package: Up to 5-A per output
    • DDV package: Up to 10-A per output

  • Can drive various types of loads -

    • Up to four solenoids or valves

    • One stepper motor

    • Two brushed-DC motors

    • One or two thermoelectric coolers (TEC)

    • One 3-phase brushless-DC motor

    • One 3-phase permanent magnet synchronous motor (PMSM)

  • Integrated current sense and regulation
    • Current sensing across high-side MOSFETs
    • Sense outputs ( IPROPI) for each half-bridge
    • ± 3.5 % sense accuracy at maximum current

    • Optional external sense resistor

  • Pin-to-pin compatible with:

    • DRV8952: 55 V, four-channel half-bridge driver

  • Separate logic supply voltage ( VCC)

  • Programmable output rise/fall time

  • Programmable fault recovery method

  • Supports 1.8-V, 3.3-V, 5.0-V logic inputs
  • Low-current sleep mode (3 µA)
  • Protection features
    • VM undervoltage lockout (UVLO)
    • Charge pump undervoltage (CPUV)
    • Overcurrent protection (OCP)
    • Thermal shutdown (OTSD)
    • Fault condition output (nFAULT)
  • Four-channel half-bridge driver
    • Independent control of each half-bridge
  • 4.5 V to 65 V operating supply voltage range
  • Low R DS(ON): 50 mΩ for each FET (24 V, 25 °C)
  • High current capacity:
    • DDW package: Up to 5-A per output
    • DDV package: Up to 10-A per output

  • Can drive various types of loads -

    • Up to four solenoids or valves

    • One stepper motor

    • Two brushed-DC motors

    • One or two thermoelectric coolers (TEC)

    • One 3-phase brushless-DC motor

    • One 3-phase permanent magnet synchronous motor (PMSM)

  • Integrated current sense and regulation
    • Current sensing across high-side MOSFETs
    • Sense outputs ( IPROPI) for each half-bridge
    • ± 3.5 % sense accuracy at maximum current

    • Optional external sense resistor

  • Pin-to-pin compatible with:

    • DRV8952: 55 V, four-channel half-bridge driver

  • Separate logic supply voltage ( VCC)

  • Programmable output rise/fall time

  • Programmable fault recovery method

  • Supports 1.8-V, 3.3-V, 5.0-V logic inputs
  • Low-current sleep mode (3 µA)
  • Protection features
    • VM undervoltage lockout (UVLO)
    • Charge pump undervoltage (CPUV)
    • Overcurrent protection (OCP)
    • Thermal shutdown (OTSD)
    • Fault condition output (nFAULT)

The DRV8962 is a wide-voltage, high-power, four-channel half-bridge driver for a wide variety of industrial applications. The device supports up to 65-V supply voltage, and integrated MOSFETs with 50 mΩ on-resistance allow up to 5-A current on each output with the DDW package; and up to 10-A current per output with the DDV package.

The device can be used for driving up to four solenoids or valves, one stepper motor, two brushed-DC motors, one BLDC or PMSM motor and up to two thermoelectric coolers (Peltier elements). The output stage of the device consists of N-channel power MOSFETs configured as four independent half-bridges, charge pump regulator, current sensing and regulation circuits, current sense outputs and protection circuitry.

Integrated current sensing across the high-side MOSFETs allows the device to regulate the current when the load is connected from output to ground. A regulation current limit can be set with an adjustable external voltage reference (VREF). Additionally, the device provides four proportional current output pins, one for each half-bridge high-side FET. Optional external sense resistors can also be connected from the PGND pins to the system ground.

A low-power sleep mode is provided to achieve ultra- low quiescent current. Internal protection features are provided for supply undervoltage lockout (UVLO), charge pump undervoltage (CPUV), output over current (OCP), and device overtemperature (OTSD).

The DRV8962 is a wide-voltage, high-power, four-channel half-bridge driver for a wide variety of industrial applications. The device supports up to 65-V supply voltage, and integrated MOSFETs with 50 mΩ on-resistance allow up to 5-A current on each output with the DDW package; and up to 10-A current per output with the DDV package.

The device can be used for driving up to four solenoids or valves, one stepper motor, two brushed-DC motors, one BLDC or PMSM motor and up to two thermoelectric coolers (Peltier elements). The output stage of the device consists of N-channel power MOSFETs configured as four independent half-bridges, charge pump regulator, current sensing and regulation circuits, current sense outputs and protection circuitry.

Integrated current sensing across the high-side MOSFETs allows the device to regulate the current when the load is connected from output to ground. A regulation current limit can be set with an adjustable external voltage reference (VREF). Additionally, the device provides four proportional current output pins, one for each half-bridge high-side FET. Optional external sense resistors can also be connected from the PGND pins to the system ground.

A low-power sleep mode is provided to achieve ultra- low quiescent current. Internal protection features are provided for supply undervoltage lockout (UVLO), charge pump undervoltage (CPUV), output over current (OCP), and device overtemperature (OTSD).
filter Find other Brushed DC (BDC) motor drivers
Download View video with transcript Video

Similar products you might be interested in

open-in-new Compare alternates
Drop-in replacement with upgraded functionality to the compared device
DRV8952 ACTIVE 50-V four-channel half-bridge driver with current sense outputs Optimized for lower voltage applications (50 V abs max)
Similar functionality to the compared device
DRV8262 ACTIVE 65-V single or dual H-bridge motor driver with integrated current sense and regulation Optimized for brushed motors
DRV8462 ACTIVE 65V, 10A dual H-bridge stepper motor driver with smart tune, stall detect and auto torque Optimized for stepper motors
DRV8844 ACTIVE 60V, 2.5A dual H-bridge motor driver, bipolar (+/-30V) supply and independent 1/2-bridge control Optimized for lower current applications
DRV8955 ACTIVE 50-V, 2.5-A, quad half-bridge driver with current sense Optimized for lower current and lower voltage applications (50 V abs max)

Technical documentation

star =Top documentation for this product selected by TI
No results found. Please clear your search and try again.
View all 5
Type Title Date
* Data sheet DRV8962 Four-channel Half-Bridge Driver with Current Sense Outputs datasheet (Rev. B) PDF | HTML 28 Sep 2023
Technical article Selecting the right level of integration to meet motor design requirements PDF | HTML 04 Jan 2024
User guide DRV84xx_DRV82x2_DRV89x2-EVM User's Guide (Rev. B) PDF | HTML 18 Jan 2023
Certificate DRV8962VEVM EU RoHS Declaration of Conformity (DoC) 16 Dec 2022
Certificate DRV8962EVM EU RoHS Declaration of Conformity (DoC) 02 Sep 2022

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Evaluation board

DRV8962EVM — DRV8962 evaluation module for quad half-bridge motor driver with current sense output

The DRV8962 EVM evaluation module showcases the features and performance of the DRV8962DDWR.

The DRV8962 is a four-channel half-bridge driver that operates from 4.5 V to 65 V to 5 A per output while supporting a wide range of load currents for various types of loads. The device integrates four (...)

User guide: PDF | HTML
Not available on TI.com
Evaluation board

DRV8962VEVM — DRV8962 evaluation module for quad half-bridge motor driver in DDV package

The DRV8962VEVM showcases the features and performance of the DRV8962DDVR. The DDV package has twice the current capability of the DDW package for this device.

The DRV8962 is a four-channel half-bridge driver that operates from 4.5 V to 65 V to 10 A per output while supporting a wide range of load (...)

User guide: PDF | HTML
Not available on TI.com
Support software

DRV84XX-DRV89X2-DRV82X2-EVM-SOFTWARE — EVM GUI and device firmware for DRV84XX_DRV89X2_DRV82X2 family

Zipped folder containing manifests and installers for both the GUI and the firmware of the DRV84XX_DRV89X2_DRV82X2 family of devices. Detailed instructions on how to use the GUI can be found in the User's Guide of the DRV84XX-DRV89X2-DRV82X2-EVM.
Supported products & hardware

Supported products & hardware

Products
Brushed DC (BDC) motor drivers
DRV8952 — 50-V four-channel half-bridge driver with current sense outputs DRV8962 — 65-V four-channel half-bridge driver with current sense outputs DRV8262 — 65-V single or dual H-bridge motor driver with integrated current sense and regulation
Stepper motor drivers
DRV8462 — 65V, 10A dual H-bridge stepper motor driver with smart tune, stall detect and auto torque DRV8452 — 50-V, 5-A, dual H-bridge stepper motor driver with smart tune, stall detect and auto-torque DRV8461 — 65-V, 3-A dual H-bridge stepper motor driver with smart tune, stall detect and auto-torque
Hardware development
Evaluation board
DRV8462EVM — DRV8462 evaluation module for stepper motor driver with automatic microstepping DRV8262EVM — DRV8262 evaluation module for single or dual H-bridge motor driver in DDW package DRV8962EVM — DRV8962 evaluation module for quad half-bridge motor driver with current sense output DRV8461EVM — DRV8461 evaluation module for DDW package DRV8462VEVM — DRV8462 evaluation module for stepper motor driver in DDV package DRV8262VEVM — DRV8262 evaluation module for single or dual H-bridge motor driver in DDV package DRV8962VEVM — DRV8962 evaluation module for quad half-bridge motor driver in DDV package
Launch Download options
Package Pins CAD symbols, footprints & 3D models
HTSSOP (DDV) 44 Ultra Librarian
HTSSOP (DDW) 44 Ultra Librarian
TI's Standard Terms and Conditions for Evaluation Items apply.

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring
Information included:
  • Fab location
  • Assembly location

Recommended products may have parameters, evaluation modules or reference designs related to this TI product.

Support & training

TI E2E™ forums with technical support from TI engineers

View all forum topics

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos