Calculation tool
TPS43337-Q1
Automotive 2V to 40V Low Iq Single Boost & Dual Fixed Output Voltage Synchronous Buck Controller
Data sheet
TPS43337-Q1
- Qualified for Automotive Applications
- AEC-Q100 Qualified With the Following Results:
- Device Temperature Grade 1:
–40°C to +125°C Ambient Operating Temperature - Device HBM ESD Classification Level H2
- Device CDM ESD Classification Level C2
- Device Temperature Grade 1:
- Two Synchronous Buck Controllers
- BuckA: Fixed Output Voltage of 3.4 V
- BuckB: Fixed Output Voltage of 1.235 V
- One Pre-Boost Controller
- Input Range up to 40 V, (Transients up to 60 V),
Operation Down to 2 V When Boost Is Enabled - Low-Power Mode IQ:
34 µA (One Buck On), 43 µA (Two Bucks On) - Low Shutdown Current Ish < 4 µA
- Boost Output Selectable: 7 V, 8.85 V, or 10 V
- Programmable Frequency and External Synchronization Range:
150 to 600 kHz - Separate Enable Inputs (ENA, ENB, ENC)
- Selectable Forced Continuous Mode or Automatic
Low-Power Mode at Light Loads - Sense Resistor or Inductor DCR Sensing for Buck Controllers
- Out-of-Phase Switching Between Buck Channels
- Peak Gate Drive Current 1.5 A
- Thermally Enhanced 38-Pin HTSSOP (DAP) PowerPAD Package
The TPS43337-Q1 includes two current-mode synchronous buck controllers and a voltage-mode boost controller. The device is ideally suited as a pre-regulator stage with low IQ requirements and for systems that must survive supply drops due to cranking events. The integrated boost controller allows the device to operate down to 2 V at the input without seeing a drop on the buck regulator output stages. At light loads, the buck controllers enable to operate automatically in low power-mode, consuming just 34 µA of quiescent current.
The buck controllers have independent soft-start capability and power-good indicators. Current foldback in the buck controllers and cycle-by-cycle current limitation in the boost controller provide external MOSFET protection. The switching frequency is programable over 150 to 600 kHz or is synchronized to an external clock in the same range
Technical documentation
No results found. Please clear your search and try again.
View all 3 | Type | Title | Date | ||
|---|---|---|---|---|
| * | Data sheet | LOW IQ, SINGLE-BOOST, FIXED-VOLTAGE DUAL SYNCHRONOUS BUCK CONTROLLER datasheet (Rev. A) | 06 Sep 2013 | |
| Design guide | TPS4333x-Q1 / TPS4335x-Q1 Design Checklist | 28 Oct 2013 | ||
| User guide | TPS4333xEVM | 01 Apr 2011 |
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
TPS43330EVM — TPS43330EVM Evaluation Module
The Texas Instruments TPS43330EVM evaluation module (EVM) helps designers evaluate the operation and performance of the TPS43330 Low Iq, Single Boost, Dual Synchronous Buck Controller.
User guide: PDF
Simulation model
TPS43337-Q1 Unencrypted PSpice Transient Model Package (Rev. A)
SLVM924A.ZIP (178 KB) - PSpice Model
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| HTSSOP (DAP) | 38 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.