GUI for evaluation module (EVM)
TAS2X20-GUI — PurePath™ Console 3 Apps for TAS2x20 EVM
PurePath™ Console 3 Apps for TAS2x20 EVM
TAS2320
15W, mono digital input Class-D speaker amplifier with 14V external boost support
Data sheet
TAS2320
- Powerful Class-D amplifier
- 15W 1% THD+N
- 15V external PVDD supply
- Best in class efficiency
- Upto 89% efficiency at system level for 8Ω load
- 14.2mW idle channel power, noise gate off
- 5mW idle channel power, noise gate on
- Integrated 1.8V Y-bridge
- High performance audio channel
- 17.2µV A-wt. idle channel noise
- 109dB Dynamic Range
- -89dB THD+N
- Low EMI performance with ERC and SSM
- < 1µs chip to chip group delay matching
- Advanced integrated features
- Signal detection high efficiency modes
- High accuracy voltage monitor & temp sensor
- Ease of use features
- Hardware pin control or I2C control
- External PVDD supply
- Clock based power up/down
- Auto clock rate detection: 16 to 192kHz
- MCLK free operation
- Thermal and over current protection
- Power Supplies and user interface
- VBAT: 2.5V to 5.5V
- VDD: 1.65V to 1.95V
- IOVDD: 1.8V or 3.3V
- PVDD: 2.5V to 15V
- I2S/TDM: 8 channels
- HW pin control or I2C based control
- 26-Pin, 0.4mm Pitch, QFN package
The TAS2320 is a mono, digital input Class-D audio amplifier designed for efficiently driving high peak power into loudspeakers.
Device is optimized to deliver best battery life for real-use cases of music playback and voice calls. Advanced efficiency optimization features like Y-bridge, and algorithms enable the device to produce best-in-class efficiency across all power regions of operation. The Class-D amplifier is capable of delivering 15W output powerusing external PVDD supply.
Up to four devices can share a common bus via I2S/TDM + I2C interfaces. The device also supports five HW Control pins that can configure the device for the desired mode of operation.
Technical documentation
No results found. Please clear your search and try again.
View all 3 | Type | Title | Date | ||
|---|---|---|---|---|
| * | Data sheet | TAS2320 15W Mono Digital Input Class-D Speaker Amp with 15V Support datasheet | PDF | HTML | 16 Sep 2024 |
| Application note | TAS2x20 Design and Layout Guidelines | PDF | HTML | 30 Sep 2024 | |
| EVM User's guide | TAS2320 Evaluation Module User's Guide | PDF | HTML | 22 Aug 2024 |
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Evaluation board
TAS2320EVM — TAS2320 evaluation module
The TAS2320EVM has been designed to demonstrate the performance of TAS2320 in a mono configuration. This tool utilizes the AC-MB to provide a USB to audio interface to the evaluation module. Up to four devices can share a common bus through I2S/TDM and I2C interfaces. The TAS2320EVM supports a (...)
Simulation tool
PSPICE-FOR-TI — PSpice® for TI design and simulation tool
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| VQFN-HR (RBG) | 26 | Ultra Librarian |
Ordering & quality
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.