This TCA9509 integrated circuit is an I2C bus/SMBus Repeater for use in I2C/SMBus systems. It can also provide bidirectional voltage-level translation (up-translation/down-translation) between low voltages (down to 0.9V) and higher voltages (2.7V to 5.5V) in mixed-mode applications. This device enables I2C and similar bus systems to be extended, without degradation of performance even during level shifting.
The TCA9509 buffers both the serial data (SDA) and the serial clock (SCL) signals on the I2C bus, thus allowing 400pF bus capacitance on the B-side. This device can also be used to isolate two halves of a bus for voltage and capacitance.
The TCA9509 has two types of drivers – A-side drivers and B-side drivers. All inputs and B-side I/Os are overvoltage tolerant to 5.5V. The A-side I/Os are overvoltage tolerant to 5.5V when the device is unpowered (VCCB and/or VCCA = 0 V).
The bus port B drivers are compliant with SMBus I/O levels, while the A-side uses a current sensing mechanism to detect the input or output LOW signal which prevents bus lock-up. The A-side uses a 1 mA current source for pull-up and a 200Ω pull-down driver. This results in a LOW on the A-side accommodating smaller voltage swings. The output pull-down on the A-side internal buffer LOW is set for approximately 0.2V, while the input threshold of the internal buffer is set about 50mV lower than that of the output voltage LOW. When the A-side I/O is driven LOW internally, the LOW is not recognized as a LOW by the input. This prevents a lock-up condition from occurring. The output pull-down on the B-side drives a hard LOW and the input level is set at 0.3 of SMBus or I2C-bus voltage level which enables B side to connect to any other I2C-bus devices or buffer.
The TCA9509 drivers are not enabled unless VCCA is above 0.8V and VCCB is above 2.5V. The enable (EN) pin can also be used to turn the drivers on and off under system control. Caution should be observed to only change the state of the EN pin when the bus is idle.
| Type | Title | Date | ||
|---|---|---|---|---|
| * | Data sheet | TCA9509 Level-Translating I2 C and SMBUS Bus Repeater datasheet (Rev. E) | PDF | HTML | 30 Oct 2024 |
| Application note | Understanding Transient Drive Strength vs. DC Drive Strength in Level-Shifters (Rev. A) | PDF | HTML | 03 Jul 2024 | |
| Application note | Resolving Improper Implementation of the Static Voltage Offset on I2C Buffers | PDF | HTML | 09 Oct 2023 | |
| Application note | Why, When, and How to use I2C Buffers | 23 May 2018 | ||
| Application note | Choosing the Correct I2C Device for New Designs | PDF | HTML | 07 Sep 2016 | |
| Application note | Understanding the I2C Bus | PDF | HTML | 30 Jun 2015 | |
| Application note | Maximum Clock Frequency of I2C Bus Using Repeaters | 15 May 2015 | ||
| Application note | I2C Bus Pull-Up Resistor Calculation | PDF | HTML | 13 Feb 2015 |
For additional terms or required resources, click any title below to view the detail page where available.
| Package | Pins | CAD symbols, footprints & 3D models |
|---|---|---|
| VSSOP (DGK) | 8 | Ultra Librarian |
| X2QFN (RVH) | 8 | Ultra Librarian |
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.